S-1110 Media and Rate Converters
10/100/1000Base-T to 1000Base-X Conversion
- 10/100/1000 Copper to 1G Fiber Media Converters
- Connect 10/100 devices to Gigabit backbone
- Dual fiber ST/SC/LC or Single fiber SC Connectors
- Extend network distances up to 160km
- Advanced features - Smart Link Pass-Through, Fiber Fault Alert, Auto-MDIX and Loopback
S-1110 Media and Rate Converters transparently connect copper to multimode or single mode fiber. It also automatically detects if the copper port speed is 10Mbps, 100Mbps, or 1G and does a rate conversion to 1G if the fiber port speed is different. These 10/100/1000 Ethernet to Gigabit Fiber Converters provide an economical path to extend the distance of an existing network, the life of non-fiber based equipment, or the distance between two devices. S-1110 Media Converters are also available with support for Power over Ethernet (PoE) and Extended Temperature ranges.
Network Administrators can "see-everything" with Perle's advanced features such as Auto-Negotiation, Auto-MDIX, Link Pass-Through, Fiber Fault Alert, and Loopback. This allows for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle's 10/100/1000 Media Converters the smart choice for IT professionals.
10/100/1000 Rate Converting to Fiber Media Converter Features
Auto-Negotiation (802.3u) |
The media converter supports auto negotiation. The 1000Base-X fiber interface negotiates according to 802.3 clause 37. The 10/100/1000Base-T negotiates according to 802.3 clause 28 and 40. The 1000Base-X will link up with its partner after the highest common denominator (HCD) is reached and the copper has linked up with its partner. The 1000Base-X will continue to cycle through negotiation transmitting a remote fault of offline (provided this is enabled through the switch setting) until the copper is linked up and the HCDs match. The media converter supports auto-negotiation of full duplex, half duplex, remote fault, full duplex pause, asymmetric pause and Auto MDI-X. |
Auto-MDIX |
Auto-MDIX (automatic medium-dependant interface crossover) detects the signaling on the copper ethernet interface to determine the type of cable connected (straight-through or crossover) and automatically configures the connection when enabled. The media converter can also correct for wires swapped within a pair. The media converter will adjust for up to 120ns of delay skew between the 1000Base-T pairs. |
Smart Link Pass-Through |
When the Link Mode switch is placed into Smart Link Pass-Through mode, the copper ethernet port will reflect the state of the 1000Base-X media converter port. This feature can be used whether fiber auto-negotiation is enabled or disabled. |
Fiber Fault Alert |
With Fiber Fault Alert the state of the 1000Base-X receiver is passed to the 1000Base-X transmitter. This provides fault notification to the partner device attached to the 1000Base-X interface of the media converter. If the 1000Base-X transmitter is off as a result of this fault it will be turned on periodically to allow the condition to clear should the partner device on the 1000Base-X be using a similar technique. This eliminates the possibility of lockouts that occur with some media converters. Applies only when fiber auto-negotiation is disabled. |
Pause (IEEE 802.3xy) | Pause signaling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed. The media converter supports pause negotiation on the 10/100/1000Base-T connection and 1000Base-X fiber connection. |
Duplex | Full and half duplex operation supported. |
Jumbo Packets | Transparent to jumbo packets up to 10KB. |
VLAN | Transparent to VLAN tagged packets. |
Remote Loopback | Capable of performing a loopback on the 1000Base-X fiber interface. |
Not what you are looking for? View all Perle product selector.
Need help? Contact Perle.
Hardware Specifications: S-1110 Media and Rate Converters
Power
Input Supply Voltage
6 - 30 vDC, unregulated (12 vDC Nominal)
Current
175 mA
Power Consumption
2.1 watts
Power Connector
5.5mm x 9.5mm x 2.1mm barrel socket
Power Adapter
Universal AC/DC adapter
100-240v AC, regulated DC adapter included
Indicators
Power / TST
This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode.
Fiber link on / Receive activity (LKF)
This green LED is operational only when power is applied. The LED is on when the 1000Base-X link is on and flashes with a 50% duty cycle when data is received.
Copper link on / Receive activity (LKC)
This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-T link is on and flashes with a 50% duty cycle when data is received.
Fiber Duplex (FDF)
This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-X link is operational in full duplex mode. The LED is off when in half duplex.
Copper Duplex (FDC)
This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-T link is operational in full duplex mode. The LED is off when in half duplex.
10/100/1000 Speed
This multi-color LED is operational only when power is applied. The LED is green when the speed of the copper ethernet port is running at 1000 Mbps. The LED is orange when the speed of the copper Ethernet port is running at 100 Mbps. The LED is off when in 10 Mbps.
Switches - accessible through a side opening in the chassis
Auto-Negotiation (802.3u)
- Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex, half duplex, pause and remote fault capabilities.
- Disabled - The media converter sets the port according to the position of the speed and duplex switches.
Link Mode
Link Mode provides a transparency to the state of the copper link allowing for simplified trouble shooting from the devices connected to the media converter.
Normal (Default — Up)
- With Fiber Auto Negotiation enabled when the copper link goes down the 1000Base-X link is brought down. The 1000Base-X link will advertise Remote Fault (Link Fault).
- With Fiber Auto Negotiation disabled the state of the copper link has no effect on the 1000Base-X link.
Smart Link Pass Through (Down)
- With Fiber Auto Negotiation enabled the behavior is as follows. When the copper link goes down the 1000Base-X link is brought down. The 1000Base-X link will advertise Remote Fault (Link Fault). When Remote Fault (Link Fault) is received on the 1000Base-X interface the copper transmitter will be turned off. When the copper receiver is off the 1000Base-X transmitter will be turned off. When the 1000Base-X receiver goes off the copper transmitter will be turned off.
- With Fiber Auto-Negotiation disabled the behavior is as follows. When the copper receiver is off the 1000Base-X transmitter will be turned off. When the 1000Base-X receiver goes off the copper transmitter will be turned off.
Fiber Fault Alert
The Fiber Fault Alert switch has meaning when Auto-Negotiation is disabled
- Enabled (Default - Up) - When the 1000Base-X receiver is off the 1000Base-X transmitter is turned off. Periodically the 1000Base-X receiver will be turned on for a short period to allow the condition to clear if the 1000Base-X link partner is using a similar feature.
- Disabled (Down)
Remote Loopback
The media converter can perform a loopback on the 1000Base-X fiber interface.
- Disabled (Default - Up)
- Enabled - The 1000Base-X receiver is looped to the 1000Base-X transmitter. The copper transmitter is taken off the interface.
Auto-MDIX (Internal Strap)
If Auto-Negotiation (802.3u) is enabled, the media converter determines the current cable pinout to use on the copper interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the copper interface to set the port MDI or MDIX whichever is appropriate.
- Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable.
- Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting.
Speed Copper
- 100 (Default)
- 10
Duplex Copper
- Full (Default)
- Half
Duplex Fiber
- Full (Default)
- Half
Connectors
10/100/1000Base-T
RJ45 connector
- 2 pair CAT5, EIA/TIA 568A/B or better cable for 10/100.
- 4 pair CAT5 UTP cable for Gigabit.
Magnetic Isolation
1.5kv
Filtering
Filtering
1024 MAC Addresses
Frame Specifications
Buffer
1000 Kbits frame buffer memory
Size
- Maximum frame size of 10,240 bytes -- Gigabit
- Maximum frame size of 2048 bytes -- Fast Ethernet
Environmental Specifications
Operating Temperature
0°C to 50°C (32°F to 122°F)
Storage Temperature
minimum range of -25°C to 70°C (-13°F to 158°F)
Operating Humidity
5% to 90% non-condensing
Storage Humidity
5% to 95% non-condensing
Operating Altitude
Up to 3,048 meters (10,000 feet)
Heat Output (BTU/HR)
7.2
MTBF (Hours)*
- Without power adaptor: 598,000 Hours
- With power adaptor: 334,000 Hours
Calculation model based on MIL-HDBK-217-FN2 @ 30°C
Chassis
Metal with an IP20 ingress protection rating
Mounting
Din Rail Kit
Optional
Rack Mount Kit
Optional
Product Weight and Dimensions
Weight
0.3 kg, 0.66 lbs
Dimensions
120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches
Packaging
Shipping Weight
0.55 kg, 1.2 lbs
Shipping Dimensions
170 x 280 x 70 mm, 6.7 x 10.2 x 2.8 inches
Regulatory Approvals
Emissions
- FCC Part 15 Class A, EN55022 Class A
- CISPR 22 Class A
- CISPR 32:2015/EN 55032:2015 (Class A)
- CISPR 24:2010/EN 55024:2010
- EN61000-3-2
Immunity
EN55024
Electrical Safety
- UL/EN/IEC 62368-1
- CAN/CSA C22.2 No. 62368-1
- UL 60950-1
- IEC 60950-1(ed 2); am1, am2
- EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
- CE
Laser Safety
- EN 60825-1
- Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11.
Environmental
Other
- ECCN: 5A991
- HTSUS Number: 8517.62.0020
- Perle Limited Lifetime Warranty
Select a Model to obtain a Part Number - Unmanaged Stand-alone Media Converters - 10/100/1000 to Fiber
Model |
Connector |
Type |
Transmit
(dBm) |
Receive
(dBm) |
Power
Budget (dBm) |
Wavelength
(nm) |
Fiber
Type |
Core
Size (um) |
Modal
Bandwidth (MHz* Km) |
Operating
Distance |
||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||||
S-1110-M2SC05 | Dual SC |
1000Base-SX |
-9.5 |
-4.0 |
-17.0 |
-3.0 |
7.5 |
850 |
MMF |
62.5 |
160 |
220 m
(722 ft) |
62.5 |
200 |
275 m
(902 ft) |
||||||||||
50 |
400 |
500 m
(1,640 ft) |
||||||||||
50 |
500 |
550 m
(1,804 ft) |
||||||||||
50 |
2000 |
1000 m
(3281 ft) |
||||||||||
S-1110-M2LC05 | Dual LC |
1000Base-SX |
-9.5 |
-4.0 |
-17.0 |
-3.0 |
7.5 |
850 |
MMF |
62.5 |
160 |
220 m
(722 ft) |
62.5 |
200 |
275 m
(902 ft) |
||||||||||
50 |
400 |
500 m
(1,640 ft) |
||||||||||
50 |
500 |
550 m
(1,804 ft) |
||||||||||
50 |
2000 |
1000 m
(3281 ft) |
||||||||||
S-1110-M2ST05 | Dual ST |
1000Base-SX |
-9.5 |
-3.0 |
-20.0 |
-3.0 |
10.5 |
850 |
MMF |
62.5 |
160 |
220 m
(722 ft) |
62.5 |
200 |
275 m
(902 ft) |
||||||||||
50 |
400 |
500 m
(1,640 ft) |
||||||||||
50 |
500 |
550 m
(1,804 ft) |
||||||||||
50 |
2000 |
1000 m
(3281 ft) |
||||||||||
S-1110-M2SC2 | Dual SC |
1000Base-LX |
-6.0 |
0.0 |
-17.0 |
-0.0 |
11 |
1310 |
MMF |
62.5 |
160 |
2 km
(1.2 mi) |
50 |
500 |
1000m
(3280ft) |
||||||||||
S-1110-M2LC2 | Dual LC |
1000Base-LX |
-9.0 |
-1.0 |
-19.0 |
-1.0 |
10 |
1310 |
MMF |
62.5 |
160 |
2 km
(1.2 mi) |
50 |
500 |
1000m
(3280ft) |
||||||||||
S-1110-M2ST2 | Dual ST |
1000Base-LX |
-6.0 |
0.0 |
-17.0 |
-0.0 |
11 |
1310 |
MMF |
62.5 |
160 |
2 km
(1.2 mi) |
50 |
500 |
1000m
(3280ft) |
||||||||||
S-1110-S2SC10 | Dual SC |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20.0 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
550 m
(1,804 ft) |
50 |
400 |
550 m
(1,804 ft) |
||||||||||
50 |
400 |
550 m
(1,804 ft) |
||||||||||
SMF |
** |
- |
10 km
(6.2 mi) |
|||||||||
S-1110-S2LC10 | Dual LC |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20.0 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
550 m
(1,804 ft) |
50 |
400 |
550 m
(1,804 ft) |
||||||||||
50 |
400 |
550 m
(1,804 ft) |
||||||||||
SMF |
** |
- |
10 km
(6.2 mi) |
|||||||||
S-1110-S2ST10 | Dual ST |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20.0 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
550 m
(1,804 ft) |
50 |
400 |
550 m
(1,804 ft) |
||||||||||
50 |
400 |
550 m
(1,804 ft) |
||||||||||
SMF |
** |
- |
10 km
(6.2 mi) |
|||||||||
S-1110-S2SC40 | Dual SC |
1000Base-EX |
-2.0 |
2.0 |
-23.0 |
-3.0 |
21.0 |
1310 |
SMF |
** |
- |
40 km
(25 mi) |
S-1110-S2LC40 | Dual LC |
1000Base-EX |
-3.0 |
2.0 |
-23.0 |
-3.0 |
20.0 |
1310 |
SMF |
** |
- |
40 km
(25 mi) |
S-1110-S2ST40 | Dual ST |
1000Base-EX |
-2.0 |
2.0 |
-23.0 |
-3.0 |
21.0 |
1310 |
SMF |
** |
- |
40 km
(25 mi) |
S-1110-S2SC70 | Dual SC |
1000Base-ZX |
-2.0 |
5.0 |
-23.0 |
-3.0 |
21.0 |
1550 |
SMF |
- |
- |
70 km
(43 mi) |
S-1110-S2LC70 | Dual LC |
1000Base-ZX |
0.0 |
5.0 |
-23.0 |
-3.0 |
23.0 |
1550 |
SMF |
- |
- |
70 km
(43 mi) |
S-1110-S2ST70 | Dual ST |
1000Base-ZX |
-2.0 |
5.0 |
-23.0 |
-3.0 |
21.0 |
1550 |
SMF |
- |
- |
70 km
(43 mi) |
S-1110-S2SC120 | Dual SC |
1000Base-ZX |
0.0 |
5.0 |
-32.0 |
-9.0 |
32 |
1550 |
SMF |
- |
- |
120 km
(75 mi) |
S-1110-S2LC120 | Dual LC |
1000Base-ZX |
0.0 |
5.0 |
-32.0 |
-9.0 |
32 |
1550 |
SMF |
- |
- |
120 km
(75 mi) |
S-1110-S2ST120 | Dual ST |
1000Base-ZX |
0.0 |
5.0 |
-32.0 |
-9.0 |
32 |
1550 |
SMF |
- |
- |
120 km
(75 mi) |
S-1110-S2SC160 | Dual SC |
1000Base-ZX |
2.0 |
5.0 |
-34.0 |
-9.0 |
36.0 |
1550 |
SMF |
- |
- |
160 km
(100 mi) |
S-1110-S2LC160 | Dual LC |
1000Base-ZX |
2.0 |
5.0 |
-34.0 |
-9.0 |
36.0 |
1550 |
SMF |
- |
- |
160 km
(100 mi) |
S-1110-S2ST160 | Dual ST |
1000Base-ZX |
2.0 |
5.0 |
-34.0 |
-9.0 |
36.0 |
1550 |
SMF |
- |
- |
160 km
(100 mi) |
Single Fiber Models Recommended use in pairs
Model |
Connector |
Type |
Transmit
(dBm) |
Receive
(dBm) |
Power
Budget (dBm) |
Wavelength
(nm) |
Fiber
Type |
Core
Size (um) |
Modal
Bandwidth (MHz* Km) |
Operating
Distance |
||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||||
S-1110-M1SC05U | Single SC |
1000Base-BX-U |
-10.0 |
-4.0 |
-17.0 |
-3.0 |
7.0 |
1310 / 1550 |
MMF |
62.5 |
500 |
500 m
(1,640 ft) |
50 |
500 |
500 m
(1,640 ft) |
||||||||||
S-1110-M1SC05D | Single SC |
1000Base-BX-D |
-10.0 |
-4.0 |
-17.0 |
-3.0 |
7.0 |
1550 / 1310 |
MMF |
62.5 |
500 |
500 m
(1,640 ft) |
50 |
500 |
500 m
(1,640 ft) |
||||||||||
S-1110-S1SC10U | Single SC |
1000Base-BX-U |
-9.0 |
-3.0 |
-20.0 |
-3.0 |
11.0 |
1310 / 1490 |
SMF |
** |
- |
10 km
(6.2 mi) |
S-1110-S1SC10D | Single SC |
1000Base-BX-D |
-9.0 |
-3.0 |
-20.0 |
-3.0 |
11.0 |
1490 / 1310 |
SMF |
** |
- |
10 km
(6.2 mi) |
S-1110-S1SC20U | Single SC |
1000Base-BX-U |
-8.0 |
-3.0 |
-22.0 |
-3.0 |
14.0 |
1310 / 1490 |
SMF |
** |
- |
20 km
(12.4 mi) |
S-1110-S1SC20D | Single SC |
1000Base-BX-D |
-8.0 |
-3.0 |
-22.0 |
-3.0 |
14.0 |
1490 / 1310 |
SMF |
** |
- |
20 km
(12.4 mi) |
S-1110-S1SC40U | Single SC |
1000Base-BX-U |
-3.0 |
2.0 |
-23.0 |
-3.0 |
20.0 |
1310 / 1490 |
SMF |
** |
- |
40 km
(25 mi) |
S-1110-S1SC40D | Single SC |
1000Base-BX-D |
-3.0 |
2.0 |
-23.0 |
-3.0 |
20.0 |
1490 / 1310 |
SMF |
** |
- |
40 km
(25 mi) |
S-1110-S1SC80U | Single SC |
1000Base-BX-U |
-2.0 |
3.0 |
-26.0 |
-3.0 |
24.0 |
1510 / 1590 |
SMF |
- |
- |
80 km
(50 mi) |
S-1110-S1SC80D | Single SC |
1000Base-BX-D |
-2.0 |
3.0 |
-26.0 |
-3.0 |
24.0 |
1590 / 1510 |
SMF |
- |
- |
80 km
(50 mi) |
S-1110-S1SC120U | Single SC |
1000Base-BX-U |
-3.0 |
2.0 |
-34.0 |
-9.0 |
31 |
1510 / 1590 |
SMF |
- |
- |
120 km
(75 mi) |
S-1110-S1SC120D | Single SC |
1000Base-BX-D |
-3.0 |
2.0 |
-34.0 |
-9.0 |
31 |
1590 / 1510 |
SMF |
- |
- |
120 km
(75 mi) |
The minimum fiber cable distance for all converters listed is 2 meters.
*A mode-conditioning adapter as specified by the IEEE standard, is required regardless of the span length. Note how the mode conditioning adapter for 62.5-um fibers has a different specification from the mode-conditioning adapter for 50-um fibers.
**ITU-T G.652 SMF as specified by the IEEE 802.3z standard.
Media Converter Accessories |
|
---|---|
4 DIN Rail Mount Bkt | DIN Rail Mounting Kit |
MCSM | Standalone media converter wall mount bracket |
Application Diagrams
Bridge 10/100 Devices to gigabit Backbone
Devices on a 10/100 ethernet switch can be connected to a Gigabit backbone through the use of rate converting 10/100/1000 Media Converters.
Single Mode / Single Fiber
When Single Strand fiber is used, a pair of Single Fiber Media Converters is needed for the copper to fiber conversion. Perle Single Fiber Media Converters are also referred to as “Up/Down” models. For example the S-1110-S1SC10U (“Up”) and S-1110-S1SC10D (“Down”), shown below, must be used in pairs. An “Up” must be matched with a “Down” peer to deal with transmit and receive frequencies separately.
S-1110-S1SC10US-1110-S1SC10D
The majority of installations for single mode fiber media converters are of the “dual connector” or “dual fiber” type where one fiber connection is used for transmit, the other for receive. These are physically “crossed” to match up the Transmit/Receive links.
However, to reduce costs, or where there are limits on available fiber, WDM technology may be utilized. WDM uses separate transmit and receive frequencies to communicate on a single fiber strand. WDM technology relies on the fact that optical fibers can carry many wavelengths of light simultaneously without interaction between each wavelength. Thus, a single fiber can carry many separate wavelength signals or channels simultaneously.
So remember, if Single Strand fiber is used, you will need an “Up” Media Converter on one side and a “Down” Media Converter on the other for copper to fiber conversion.
Perle offers a wide variety of Single Fiber (“Up/Down”) Media Converters to connect 10BaseT, Fast Ethernet and Gigabit to single fiber. Whether you need Managed or Unmanaged, Standalone or Modular Chassis Based, 20km or 120km, Perle has the right model to meet your fiber conversion requirement.
Filter your options to find the right hardware for your application
Viewing 198 of 198 products
Click on a part number for ordering information
Product Image
Product Description
Power Cord & Part No.
S-1110-M2SC05 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-SX 850nm multimode (SC) [550 m/1804 ft.]
S-1110-M2LC05 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-SX 850nm multimode (LC) [550 m/1804 ft.]
S-1110-S2LC10 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-LX/LH 1310 nm single mode (LC) [10 km/6.2 miles] or multimode (LC) [550 m/1804 ft.] using a mode cond
S-1110-S2SC10 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-LX/LH 1310 nm single mode (SC) [10 km/6.2 miles] or multimode (SC) [550 m/1804 ft.] using a mode cond
S-1110-S2LC40 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-EX 1310 nm single mode (LC) [40 km/24.9 miles]
S-1110-S2SC70 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-ZX 1550 nm single mode (SC) [70 km/43.5 miles]
S-1110-S2LC70 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-ZX 1550 nm single mode (LC) [70 km/43.5 miles]
S-1110-S1SC10U - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-BX 1310nm TX / 1490nm RX single strand single mode (SC) [10 km/6.2 miles]
S-1110-S1SC10D - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-BX 1490nm TX / 1310nm RX single strand single mode (SC) [10 km/6.2 miles]
S-1110-M2ST05 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-SX 850nm multimode (ST) [550 m/1804 ft.]
S-1110-S2ST10 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-LX/LH 1310 nm single mode (ST) [10 km/6.2 miles]
S-1110-S2SC40 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-EX 1310 nm single mode (SC) [40 km/24.9 miles]
S-1110-S2ST40 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-EX 1310 nm single mode (ST) [40 km/24.9 miles]
S-1110-S2ST70 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-ZX 1550 nm single mode (ST) [70 km/43.5 miles]
S-1110-S2SC120 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-EZX 1550 nm single mode (SC) [120 km/74.6 miles]
S-1110-S2ST120 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-EZX 1550 nm single mode (ST) [120 km/74.6 miles]
S-1110-S2LC120 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-EZX 1550 nm single mode (LC) [120 km/74.6 miles]
S-1110-S2ST160 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-ZX 1550 nm single mode (ST) [160 km/100 miles]
S-1110-S2SC160 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-ZX 1550 nm single mode (SC) [160 km/100 miles]
S-1110-S2LC160 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-ZX 1550 nm single mode (LC) [160 km/100 miles]
S-1110-S1SC20U - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-BX 1310nm TX / 1490nm RX single strand fiber, single mode (SC) [20 km/12.4 miles]
S-1110-S1SC20D - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-BX 1490nm TX / 1310nm RX single strand fiber, single mode (SC) [20 km/12.4 miles]
S-1110-S1SC40U - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-BX 1310nm TX / 1490nm RX single strand fiber, single mode (SC) [40 km/25 miles]
S-1110-S1SC40D - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-BX 1490nm TX / 1310nm RX single strand fiber, single mode (SC) [40 km/25 miles]
S-1110-S1SC80U - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-BX 1510nm TX / 1590nm RX single strand fiber, single mode (SC) [80 km/50 miles]
S-1110-S1SC80D - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-BX 1590nm TX / 1510nm RX single strand fiber, single mode (SC) [80 km/50 miles]
S-1110-S1SC120U - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-BX 1510nm TX / 1590nm RX single strand fiber, single mode (SC) [120 km/75 miles]
S-1110-S1SC120D - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-BX 1590nm TX / 1510nm RX single strand fiber, single mode (SC) [120 km/75 miles]
S-1110-M2SC2 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-LX 1310nm Extended multimode (SC) [2km /6562 ft.]
S-1110-M2ST2 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-LX 1310nm Extended multimode (ST) [2km /6562 ft.]
S-1110-M2LC2 - 10/100/1000 Gigabit Ethernet Stand-Alone Media and Rate Converter. 10/100/1000Base-T (RJ-45) [100 m/328 ft.] to 1000Base-LX 1310nm Extended multimode (LC) [2km /6562 ft.]
S-1110-M1SC05D - 10/100/1000 Gigabit Ethernet Media and Rate Converter. 10/100/1000BASE-T (RJ-45) [100 m/328 ft.] to 1000Base-BX 1550nm TX / 1310nm RX single strand fiber, multimode (SC) [550 m/1804 ft]
S-1110-M1SC05U - 10/100/1000 Gigabit Ethernet Media and Rate Converter. 10/100/1000BASE-T (RJ-45) [100 m/328 ft.] to 1000Base-BX 1310nm TX / 1550nm RX single strand fiber, multimode (SC) [550 m/1804 ft]
Related Accessories
Accessory Image
Accessory Description
Part No.
DIN Rail Mounting Kit for 4 & 8 port IOLAN desktop models, all Stand-Alone Media Converters and all Stand-alone Ethernet Extenders. Two of these brackets are required for the 8 port STS8-D model.
Standalone media converter wall / rack mount bracket