C-110 Media and Rate Converter Module

10/100Base-TX to 100Base-X Conversion

10/100Base-TX to 100Base-X Fiber Media Converters
Extend network distances up to 120km
Advanced features - Link Pass-Through, Far-End Fault, Auto-MDIX and Loopback
High density applications with Perle Media Converter Chassis

Installed in a high density Perle Media Converter Chassis, Perle's line of feature rich 10/100 Rate Converting to Fiber Media Converters transparently connect 10/100 Ethernet to fiber. Our 10/100 converters provide an economical path to extend the distance of an existing network, the life of non-fiber based equipment, or the distance between two devices.

Network Administrators can "see-everything" with Perle's advanced features such as Auto-Negotiation, Auto-MDIX, Link Pass-Through, Far End Fault, and Remote Loopback. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle's 10/100 Ethernet media converter modules the smart choice for IT professionals.

Media Converter 10/100 to Fiber Features

Auto-Negotiation (802.3u)	The media converter supports auto negotiation on the 10/100Base-TX interface.
Auto-MDIX	Auto-MDIX (automatic medium-dependant interface crossover) detects the signaling on the UTP interface to determine the type of cable connected (straight-through or crossover) and automatically configures the connection when enabled. With Auto-MDIX enabled, either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable.
Link Pass-Through	With Link Pass-Through the state of the UTP receiver is passed to the fiber transmitter to make the media converter appear transparent to the end devices that are connected. In addition if Far-End Fault is enabled the media converter can turn off the 10/100Base-TX transmitter when a FAR-End Fault is received. Using Link Pass-Through with Far-End Fault minimizes data loss when a fault occurs. Should a fault occur, the end devices have the indication of a failure available to them making trouble shooting easier.
Far-End Fault (FEF)	The media converter implements the 802.3 standard for Far-End Fault for the indication and detection of remote fault conditions on the 100Base-X fiber connection. With Far-End Fault enabled the media converter transmits the Far-End Fault Indication over the 100Base-X fiber connection whenever a receive failure is detected on the 100Base-X fiber connection. The media converter continuously monitors the100Base-X fiber connection for a valid signal. The action the media converter takes on receiving a Far-End Fault Indication is dependent on the Link Pass-Through switch setting.
Pause (IEEE 802.3xy)	Pause signaling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed. The media converter supports pause negotiation on the 10/100Base-TX copper connection.
VLAN	The media converter is transparent to VLAN tagged packets.
Remote Loopback	The media converter is capable of performing a loopback on the fiber port.

Hardware Specifications: C-110 Media and Rate Converter Module

Indicators

Power / TST

This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode.

Fiber link on / Receive activity (LKF)

This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is on and flashes with a 50% duty cycle when data is received.

Copper link on / Receive activity (LKC)

This green LED is operational only when power is applied. The LED is on when the 100Base-TX link is on and flashes with a 50% duty cycle when data is received.

Fiber Duplex (FDF)

This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is operational in full duplex mode. The LED is off when in half duplex.

Copper Duplex (FDC)

This green LED is operational only when power is applied. The LED is on when the 10/100Base-TX link is operational in full duplex mode. The LED is off when in half duplex.

10/100 Speed

This green LED is operational only when power is applied. The LED is on when the speed of the copper Ethernet port is running at 100 MBPS. The LED is off when in 10 MBPS

Switches: On-Board

Auto-Negotiation (802.3u)

Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 100Base-TX interface. It is set to advertise full duplex.
Disabled - The media converter sets the port according to the position of the speed and duplex switches.

Link Pass Through

Enabled (Default) - When the state of the receiver is changed on the 100Base-TX interface it is reflected on the 100Base-FX fiber transmitter. When the state of the receiver on the 100Base-FX interface is changed it is reflected on the 100Base-TX transmitter.
When a Far-End Fault Indication is received on the fiber interface the 100Base-TX transmitter is turned off. When the Far-End Fault Indication is cleared the transmitter is turned back on.

Disabled - The 100Base-TX and the 100Base-FX fiber interface operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the 100Base-TX interface.

Far-End Fault (FEF)

Enabled (Default) - The media converter transmits the Far-End Fault Indication over the 100Base-X fiber connection whenever a receive failure is detected on the 100Base-X fiber connection. The media converter continuously monitors the 100Base-X fiber connection and clears the Far-End Fault Indication condition when a valid signal is received.
Disabled - Far-End Fault Indications are not transmitted regardless of the condition of the receive signal on the 100Base-FX fiber connection.

Remote Loopback

The media converter can perform a loopback on the 100Base-X fiber interface.

Disabled (Default - Up)
Enabled - The 100Base-X receiver is looped to the 100Base-X transmitter. The 100Base-TX transmitter is taken off the interface.

Auto-MDIX (Strap)

If Auto-Negotiation (802.3u) is enabled, the media converter uses the HP Auto-MDIX method for the 100Base-TX interface.

If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the 100Base-TX interface to set the port MDI or MDIX whichever is appropriate.

Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable.
Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting.

Speed Copper

100 (Default)
10

Duplex Copper

Full (Default)
Half

Duplex Fiber

Full (Default)
Half

Connectors

100Base-TX

RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable

Magnetic Isolation

1.5kv

Fiber Optic Cable

Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron
Single Mode: 9/125 micron (ITU-T 625)

Filtering

1024 MAC Addresses

Frame Specifications

Buffer

512 Kbits frame buffer memory

Size

Maximum frame size of 2048 bytes

Environmental Specifications

Operating Temperature

0°C to 50°C (32°F to 122°F)

Storage Temperature

minimum range of -25°C to 70°C (-13°F to 158°F)

Operating Humidity

5% to 90% non-condensing

Storage Humidity

5% to 95% non-condensing

Operating Altitude

Up to 3,048 meters (10,000 feet)

Heat Output (BTU/HR)

7.2

Maximum Power Consumption (Watts)

2.1

MTBF (Hours)*

598,000 Hours

Calculation model based on MIL-HDBK-217-FN2 @ 30°C

Mechanical - Hot Swapping Card

Edge Connecter

32 pin DIN 41612 / IEC 60603-2 Type B/2 Male. Fist make, last break for ground and power

Card insertion and removal

Captive thumb screws enable fast insertion and removal. Can be further tighten with a screwdriver.

Product Weight

Weight

0.15 kg, 0.33 lbs

Packaging

Shipping Weight

0.33 kg, .73 lbs

Shipping Dimensions

203 x 38 x 152 mm, 8 x 1.5 x 6 inches

Regulatory Approvals

Emissions

FCC Part 15 Class A, EN55022 Class A

CISPR 22 Class A
CISPR 32:2015/EN 55032:2015 (Class A)
CISPR 24:2010/EN 55024:2010

EN61000-3-2

Immunity

EN55024

Electrical Safety

UL/EN/IEC 62368-1
CAN/CSA C22.2 No. 62368-1

UL 60950-1
IEC 60950-1(ed 2); am1, am2
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013

Laser Safety

EN 60825-1
Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11.

Environmental

Reach, RoHS and WEEE Compliant

Other

ECCN: 5A991
HTSUS Number: 8517.62.0020
Perle Limited Lifetime Warranty

Select a Model to obtain a Part Number - Unmanaged Media Converter Chassis Modules - Fast Ethernet to Fiber

Model	Connector	Type	Transmit (dBm)		Receive (dBm)		Power Budget (dBm)	Wavelength (nm)	Fiber Type	Operating Distance
Model	Connector	Type	Min	Max	Min	Max	Power Budget (dBm)	Wavelength (nm)	Fiber Type	Operating Distance
C-110-M2ST2	Dual ST	100Base-FX	-20.0	-12.0	-31.0	-14.0	11.0*	1310	MMF	2 km (1.2 mi)
C-110-M2SC2	Dual SC	100Base-FX	-20.0	-12.0	-31.0	-14.0	11.0*	1310	MMF	2 km (1.2 mi)
C-110-M2LC2	Dual LC	100Base-FX	-20.0	-12.0	-30.0	-14.0	10.0*	1310	MMF	2 km (1.2 mi)
C-110-S2ST20	Dual ST	100Base-LX	-18.0	-7.0	-32.0	-3.0	14.0	1310	SMF	20 km (12.4 mi)
C-110-S2SC20	Dual SC	100Base-LX	-18.0	-7.0	-32.0	-3.0	14.0	1310	SMF	20 km (12.4 mi)
C-110-S2LC20	Dual LC	100Base-LX	-15.0	0.0	-34.0	-5.0	19.0	1310	SMF	20 km (12.4 mi)
C-110-S2ST40	Dual ST	100Base-EX	-5.0	0.0	-34.0	-3.0	29.0	1310	SMF	40 km (25 mi)
C-110-S2SC40	Dual SC	100Base-EX	-5.0	0.0	-34.0	-3.0	29.0	1310	SMF	40 km (25 mi)
C-110-S2LC40	Dual LC	100Base-EX	-5.0	0.0	-34.0	-3.0	29.0	1310	SMF	40 km (25 mi)
C-110-S2ST80	Dual ST	100Base-ZX	-5.0	0.0	-34.0	-3.0	29.0	1550	SMF	80 km (50 mi)
C-110-S2SC80	Dual SC	100Base-ZX	-5.0	0.0	-34.0	-3.0	29.0	1550	SMF	80 km (50 mi)
C-110-S2LC80	Dual LC	100Base-ZX	-5.0	0.0	-34.0	-3.0	29.0	1550	SMF	80 km (50 mi)
C-110-S2ST120	Dual ST	100Base-ZX	0.0	5.0	-35.0	-3.0	35.0	1550	SMF	120 km (75 mi)
C-110-S2SC120	Dual SC	100Base-ZX	0.0	5.0	-35.0	-3.0	35.0	1550	SMF	120 km (75 mi)
C-110-S2LC120	Dual LC	100Base-ZX	0.0	5.0	-34.0	-3.0	34.0	1550	SMF	120 km (75 mi)

Single Fiber Models Recommended use in pairs

Model	Connector	Type	Transmit (dBm)		Receive (dBm)		Power Budget (dBm)	Wavelength (nm)	Fiber Type	Operating Distance
Model	Connector	Type	Min	Max	Min	Max	Power Budget (dBm)	Wavelength (nm)	Fiber Type	Operating Distance
C-110-M1ST2U	Single ST	100Base-BX-U	-15.0	0.0	-28.0	-8.0	13.0	1310 / 1550	MMF	2 km (1.2 mi)
C-110-M1ST2D	Single ST	100Base-BX-D	-15.0	0.0	-28.0	-8.0	13.0	1550 / 1310	MMF	2 km (1.2 mi)
C-110-M1SC2U	Single SC	100Base-BX-U	-15.0	0.0	-28.0	-8.0	13.0	1310 / 1550	MMF	2 km (1.2 mi)
C-110-M1SC2D	Single SC	100Base-BX-D	-15.0	0.0	-28.0	-8.0	13.0	1550 / 1310	MMF	2 km (1.2 mi)
C-110-S1ST20U	Single ST	100Base-BX-U	-14.0	-8.0	-32.0	-3.0	18.0	1310 / 1550	SMF	20 km (12.4 mi)
C-110-S1ST20D	Single ST	100Base-BX-D	-14.0	-8.0	-32.0	-3.0	18.0	1550 / 1310	SMF	20 km (12.4 mi)
C-110-S1SC20U	Single SC	100Base-BX-U	-14.0	-8.0	-32.0	-3.0	18.0	1310 / 1550	SMF	20 km (12.4 mi)
C-110-S1SC20D	Single SC	100Base-BX-D	-14.0	-8.0	-32.0	-3.0	18.0	1550 / 1310	SMF	20 km (12.4 mi)
C-110-S1SC40U	Single SC	100Base-BX-U	-8.0	-3.0	-33.0	-3.0	25.0	1310 / 1550	SMF	40 km (25 mi)
C-110-S1SC40D	Single SC	100Base-BX-D	-8.0	-3.0	-33.0	-3.0	25.0	1550 / 1310	SMF	40 km (25 mi)

The minimum fiber cable distance for all converters listed is 2 meters.

*Based on use with 62.5/125 micron multimode fiber.

High Density Fiber Distribution from UTP Switch Equipment at Corporate Headquarters

In this enterprise campus application, up to 19 Perle C-110 10/100 Media Converters are installed in the MCR1900 Media Converter Chassis. A remote fiber enabled Ethernet switch is connected directly to the central MCR1900 Chassis. A standalone S-110 Media Converter converts the fiber to Ethernet in a fiber-to-desktop application. Another S-110 Fiber Media Converter is connected to a remote office Ethernet switch. In all cases, multimode or single-mode fiber can be used. Fiber links can be extended up to 120km using single-mode fiber.

10/100 – Extend Network between Ethernet Hubs

Extend the network distance between two Ethernet Hubs

A pair of 10/100 media converters can extend the distance between hubs across a fiber link up to 120km in length.

Extend Network between Ethernet Hubs Diagram

10/100 – Extend Network between 10Mbps and Fast Ethernet

Extend the network distance between legacy 10Mbps copper Ethernet to Fast Ethernet infrastructure

A pair of 10/100 media converters can extend the distance between a legacy 10Mbps device to a Fast Ethernet switch across a fiber link up to 120km in length.

10/100 – Extend Network between Half-Duplex Hubs

Extend the network distance between two Ethernet half-duplex hubs

A pair of 10/100 media converters can extend the distance between hubs across a fiber link up to 120km in length. They also isolate the collision domains, associated with half-duplex, from crossing the fiber link.

10/100 – Extend Network between Half-Duplex Hub and Switch

Extend the network distance between an Ethernet half-duplex hub and a full-duplex switch

A pair of 10/100 media converters can extend the distance between a half-duplex hub and a full-duplex switch across a fiber link up to 120km in length. They also isolate the collision domains, associated with half-duplex, from crossing the fiber link. In this scenario, the media converter connected to the switch must be forced to half-duplex.

10/100 – Extend Network between two legacy 10Mbps Devices

Extend the network distance between legacy 10Mbps copper Ethernet devices

A pair of 10/100 media converters can extend the distance between two legacy 10Mbps devices across a fiber link up to 120km in length.

Single Mode / Single Fiber

Connect copper ports over a single fiber strand ( also referred to as “Bi-Directional” BiDi )

When Single Strand fiber is used, a pair of Single Fiber Media Converters is needed for the copper to fiber conversion. Perle Single Fiber Media Converters are also referred to as “Up/Down” models. For example the C-110-S1SC20U (“Up”) and C-110-S1SC20D (“Down”), shown below, must be used in pairs. An “Up” must be matched with a “Down” peer to deal with transmit and receive frequencies separately.

C-110-S1SC20UC-110-S1SC20D

The majority of installations for single mode fiber media converters are of the “dual connector” or “dual fiber” type where one fiber connection is used for transmit, the other for receive. These are physically “crossed” to match up the Transmit/Receive links.

However, to reduce costs, or where there are limits on available fiber, WDM technology may be utilized. WDM uses separate transmit and receive frequencies to communicate on a single fiber strand. WDM technology relies on the fact that optical fibers can carry many wavelengths of light simultaneously without interaction between each wavelength. Thus, a single fiber can carry many separate wavelength signals or channels simultaneously.

So remember, if Single Strand fiber is used, you will need an “Up” Media Converter on one side and a “Down” Media Converter on the other for copper to fiber conversion.

Perle offers a wide variety of Single Fiber (“Up/Down”) Media Converters to connect 10BaseT, Fast Ethernet and Gigabit to single fiber. Whether you need Managed or Unmanaged, Standalone or Modular Chassis Based, 20km or 120km, Perle has the right model to meet your fiber conversion requirement.

Installation and user guides

EU Declaration of Conformity

Fiber Media Converter FAQ Knowledgebase

Single Mode / Single Strand (WDM) Fiber

WDM technology reduces costs and maximizes fiber usage by transmitting on separate frequencies within a single fiber that can carry multiple light wavelengths simultaneously without interference. WDM comes in two forms: conventional/coarse (CWDM) and dense (DWDM), which use different wavelength patterns.

Calculating and Understanding Optical Power Budgets

The steps explain how to keep the remaining available power budget number positive, so you can be assured that your fiber network will deliver the required performance over the life of the installation.

Link Passthrough - Maintaining a Transparent Copper-Ethernet to Fiber Link

Understanding the need for an onboard processor in the media converter that continuously monitors the status of the links connected to its transceiver ports.

York University use Perle Media Converters in Field Robotics Research Network

Perle Gigabit Media Converters provide fiber to copper conversion and POE+ to WLAN Access Points inside NEMA Weatherproof Enclosures.

Navtech use Perle Industrial Switches & Media Converters in military airbourne surveillance system

Navtech Systems supplies airborne surveillance video downlinks globally, and secure, real-time transmission and distribution of data is crucial. Perle units are used in the network on the ground to access the imagery and data received from the aircraft. Perle products are high-quality, solid, secure, and reliable.

Gaming Innovation Group use Perle 10G Media Converters in Data Center

Perle Media Converters facilitate Fiber to 10 GbE Copper Conversion at the GIG Data Center in Malta. They offer flexibility with different modules in one chassis and enable seamless and reliable connectivity for single mode and multimode equipment.

ERH install Perle Media Converters in UK Smart Motorway

ERH upgraded 300 CCTV cameras in Wales with new HD Ethernet cameras. Perle media converters allowed multiple cameras to feed into a chassis unit for image transfer to the main network and video wall.

Creating a hybrid video surveillance system using Analog and IP Cameras

Diagram for Media Converters in Video Surveillance System

Dragon LNG installed Perle Fiber Media Converters to integrate new IP cameras into the existing surveillance system. Hybrid setup with analog cameras is flexible and scalable for more IP cameras in the future.

Fiber to Ethernet can support large-scale retail networks

Integrating copper and fiber in a retail network

Integrating copper and fiber cabling in retail network environments

Enterprise Network fiber–optic deployment – Using Media Converters to unlock performance and reduce costs during upgrades

As the network upgrades are traditionally complex and expensive. Fiber to Copper Media Converters can simplify both of these issues for businesses and enable them to improve network performance.

Media Converters offer major benefits during Backhaul Network fiber-optic upgrades

Media Converters in Backhaul Network fiber-optic upgrades

Fiber to Ethernet Media Converters simplify the process by allowing businesses to use optical technologies to support high-bandwidth backhaul networks that connect to low-bandwidth Ethernet networks accessed by the end user.

Media Converters extend campus environment LANs

Media Converters in a Campus Environment Diagram

The use of chassis-based media converters is a cost effective means of providing fiber connectivity to enable long distance data transfer in campus networks.

Media Converters offer flexible expansion in Horizontal Networks

Media Converters offer flexible expansion in Horizontal Networks. Media Converters ease the integration of fiber cabling to extend network distances avoid EMI disruptions and tighten data security

ISPs improve residential network performance through media conversion

Fiber in Residential Media Converter Diagram

ISPs improve residential network performance through media conversionby using media converters to integrate fiber-optic infrastructures and provide high-speed data services.

Media conversion can unlock the potential of Metropolitan Area Networks (MANs)

Media Converters are essential for MAN deployment, facilitating seamless transition between the local Ethernet setup and the dark fiber. They enable consistent protocol handling during data transmissionresulting in significant performance enhancements over WAN systems.

Avoiding common mistakes in fiber-optic network deployment

This is the first in a three-part series on major problems that can occur when businesses rush to deploy a fiber-optic cabling infrastructure.

Do I need an Ethernet Extender or a Media Converter?

Understand when you need an Ethernet Extender or a Media Converter as they support a wide variety of protocols, data rates, and media types to integrate seamlessly into various network infrastructures.

C-110 Media and Rate Converter Module

10/100Base-TX to 100Base-X Conversion

Media Converter 10/100 to Fiber Features

Hardware Specifications: C-110 Media and Rate Converter Module

Application Diagrams