S-10G Media Converters
10 Gigabit Copper and Fiber Converters
- Fiber to Fiber, copper to fiber and copper to copper conversion
- 2 empty slots that use a variety of 10G transceivers supplied by Perle or other MSA compliant XFPs
- Advanced features –Smart Link Pass-Through, Fiber Fault Alert, Built-in Link Test Generator and Loopback
- Support for Power Level 1,2,3 as well as high-power Level 4 XFPs
- Optical signal regeneration: 3R (re-amplify, reshape, and retime)
Perle S-10G Media Converters transparently connect 10 Gigabit Ethernet links over multimode or single mode fiber. Each 10GbE Media Converter comes with two pluggable transceiver ports that support fiber to fiber, copper to fiber or copper to copper media conversion.
Fiber to Fiber and Copper to Fiber conversion is achieved by inserting XFP fiber transceivers that support multimode and single-mode fiber, including CWDM/DWDM wavelengths. Copper to copper is achieved by inserting XFP 10Gbase-CX4 transceivers.
The empty transceiver ports on the S-10G Media Converters allow for flexible network configurations to meet any requirement using a variety of 10G transceivers supplied by Perle or other manufacturers of MSA compliant XFPs.
Perle 10 Gigabit Ethernet to Fiber Converters provide an economical path to extend the distance of an existing 10GbE link. Network Administrators can “see-everything” with Perle’s advanced features such as Smart Link Pass-Through, Fiber Fault Alert, a built-in Link Test capability and Loopback. This allows for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle S-10G Media Converters the smart choice for IT professionals. 10G Media Converters are also available for managed networks with AAA security.
S-10G Media Converter Features
Smart Link Pass-Through |
|
Fiber Fault Alert |
With Fiber Fault Alert the state of the 10 Gigabit Ethernet receiver is passed to the transmitter. This provides fault notification to the partner device attached to the 10G Ethernet interface of the media converter. |
3R – Optical Signal Regeneration |
Optical signal regeneration: 3R (Re-amplify, Reshape, and Retime the signal) ensures that there is a quality link at 10 Gigabit speeds. |
Built-in Link Test |
When enabled, the built-in packet generator transmits Ethernet test frames to its 10 Gigabit Ethernet peer. The remote media converter will auto-detect the test frames and loopback the test frames. Any frames received in error, will cause the Power, LK1 and LK2 LEDs to illuminate in a specific combination to identify the error. During the test different bit test patterns will be utilized every 5 seconds ensuring a thorough link test. |
Test Mode Auto-detect |
No switches are required to be flipped in order to go into test mode. The remote media converter will enter test mode automatically when requested by its central site peer. This virtually eliminates unnecessary truck rolls to a remote site when diagnosing a link failure. |
EDC Mode Control |
Electronic Dispersion Compensation (EDC) is an algorithmic method used to compensate for optical dispersion that occurs on high speed 10 Gigabit links. EDC mode settings are automatically configured by the media converter based on the information retrieved from the XFP module. This will enable proper operation for extended multimode 10GBase-LRM as well as active or passive copper cabling. |
Module Temperature Protection |
Protects your DOM/DMI capable XFP module by monitoring its internal temperature and will automatically shut down the XFP if the module is operating above its maximum temperature threshold. |
High Power Level 4 XFPs |
High powered Level 4 XFPs are supported in XTSH and XTXH models. |
Jumbo Packets |
Transparent to Jumbo Frames with a maximum MTU size of 10,024 bytes |
VLAN |
Transparent to VLAN tagged packets. |
Power Strain Relief strap | A strain relief strap is provided to ensure a solid and secure power connection to the media converter. Ideal for areas that may be exposed to any vibration. |
Remote Loopback | Capable of performing a loopback on the 10 Gigabit interface. In this mode, all frames received on the port in loopback mode will be transmitted back. This provides users with the capability of utilizing their own in-house test generators for testing the link. |
Hardware Specifications: S-10G Media Converters
Power
Input Supply Voltage
9 - 30 vDC, unregulated (12 vDC Nominal)
Maximum Power Consumption (Watts)
- XTX: 12.0*
- XTXH: 16.8*
Total Transceiver power supports (watts)
- XTX: 7.0
- XTXH: 11.0
Power Connector
5.5mm x 9.5mm x 2.1mm barrel socket
Power Adapter
Universal AC/DC adapter
100-240v AC, regulated AC/12v DC adapter included
Indicators
Power / TST
- On: Power indication and in normal operation
- Blinking slowly: the unit is in loopback or test mode (either port)
- Red solid: the unit has a hardware error (upon power up)
- Red and blinking: the unit has a hardware error specified by combination of LK1 and LK2
LK1, LK2
- On: Fiber link present
- Blinking quickly: Fiber link present and receiving data.(including test data)
- Blinking slowly: Fiber link disabled because the other fiber link went down.
- Blinking 1 sec on 3 sec off – module shut down due to high temperature.
- Off: No fiber link present or no module inserted
Switches - accessible through a side opening in the chassis
Smart Link Pass-Through
When the Smart Link Pass-Through switch is enabled (default), each port will reflect the state of its port peer. In this mode, if a link loss is detected on one port, the transmit signal on the other port is disabled “passing through” the state of the failed link. This enables managed switches and other devices to report link failures to their network NMS.
When the switch is in the down position, Smart Link Pass-Through is disabled. If a link loss is detected on one port, the transmit signal remains enabled on the other port.
Fiber Fault Alert
Enabled (Default - Up)
With Fiber Fault Alert the state of the 10 Gigabit ethernet receiver is passed to the transmitter. This provides fault notification to the partner device attached to the 10G ethernet interface of the media converter
EDC Mode
Electronic Dispersion Compensation (EDC) is an algorithmic method used to compensate for optical dispersion that occurs on high speed 10 Gigabit links. EDC mode settings are automatically configured by the media converter based on the information retrieved from the SFP+ or XFP module. This will enable proper operation for extended multimode 10GBase-LRM as well as active or passive copper cabling.
In the default UP switch position the media converter will automatically set the 10G transceiver to match the EDC type declared by the SFP+ / XFP module to either to “linear” or “limiting”.
In the event that there is a mismatch, setting the switch to the Down position on the media converter will flip the setting to that declared by the module.
Loopback
Capable of performing a loopback on each 10 Gigabit interface. In this mode, all frames received on the port in loopback mode will be transmitted back. This provides users with the capability of utilizing their own in-house test generators for testing the link.
Connectors
Pluggable 10G Fiber Transceiver slots (Hot insertion and removable)
Two 10 Gigabit XFP Slots
- Power level 1,2,3
- Power Level 4 (XTSH model)
Voltages supplied to XFP slots
1.8V, 3.3V, 5V and -5.2V
Supported 10 Gigabit Fiber pluggable transceivers
IEEE 802.3ae compliant:
- 10GBase-SR
- 10GBase-LRM
- 10GBase-LR
- 10GBase-ER
- 10GBase-ZR
CWDM/DWDM
Supported 10 Gigabit Copper pluggable transceivers
IEEE 802.3ak compliant:
- XFP 10GBase-CX4 copper
Environmental Specifications
Operating Temperature
0°C to 50°C (32°F to 122°F)
Storage Temperature
minimum range of -25°C to 70°C (-13°F to 158°F)
Operating Humidity
5% to 90% non-condensing
Storage Humidity
5% to 95% non-condensing
Operating Altitude
Up to 3,048 meters (10,000 feet)
Heat Output (BTU/HR)
- XTX: 41.0
- XTXH: 57.3
MTBF (Hours)
- XTX & XTXH - without power adaptor: 332,711 Hours
- XTX - with power adaptor: 196,235 Hours
- XTXH - with power adaptor: 210,748 Hours
Calculation model based on MIL-HDBK-217-FN2 @ 30°C
Mounting
Din Rail Kit
Optional
Wall / Rack Mount Kit
Optional
Product Weight and Dimensions
Product Weight
0.38 kg, 0.84 lbs
Product Dimensions
8 x 12 x 4.2 cm (3.1 x 4.7 x 1.7 inches)
Shipping Weight
0.66 kg, 1.46 lbs
Shipping Dimensions
26 x 17 x 7 cm (10.2 x 6.7 x 2.8 inches)
Regulatory Approvals
Emissions
- FCC Part 15 Class A, EN55022 Class A
- CISPR 22 Class A
- CISPR 32:2015/EN 55032:2015 (Class A)
- CISPR 24:2010/EN 55024:2010
- EN61000-3-2
Immunity
EN55024
Electrical Safety
- UL/EN/IEC 62368-1
- CAN/CSA C22.2 No. 62368-1
- UL 60950-1
- IEC 60950-1(ed 2); am1, am2
- EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
- CE
Environmental
Other
- ECCN: 5A991
- HTSUS Number: 8517.62.0020
- Perle Limited Lifetime Warranty
*Maximum rating for both media converter and modules inserted. Actual rating is dependent on the power consumption of the SFP+/XPF modules inserted.
Click on 'Model Name' to see part numbers
Model Name | Port | Slot | SFP+ Power Levels | XFP Power Levels |
Maximum Total Transceiver Power Supported |
---|---|---|---|---|---|
S-10G-XTX | Port 1 | XFP | - | Level 1 (up to 1.0 watts) | 7.0 watts |
- | Level 2 (1.5 to 2.5 watts) | ||||
- | Level 3 (2.5 to 3.5 watts) | ||||
Port 2 | XFP | - | Level 1 (up to 1.0 watts) | ||
- | Level 2 (1.5 to 2.5 watts) | ||||
- | Level 3 (2.5 to 3.5 watts) | ||||
S-10G-XTXH | Port 1 | XFP | - | Level 1 (up to 1.0 watts) | 11.0 watts |
- | Level 2 (1.5 to 2.5 watts) | ||||
- | Level 3 (2.5 to 3.5 watts) | ||||
- | Level 4 (3.5 to 5.5 watts) | ||||
Port 2 | XFP | - | Level 1 (up to 1.0 watts) | ||
- | Level 2 (1.5 to 2.5 watts) | ||||
- | Level 3 (2.5 to 3.5 watts) | ||||
- | Level 4 (3.5 to 5.5 watts) |
Application Diagrams
10 Gigabit Ethernet Fiber Repeater
Create a 10 Gigabit Ethernet fiber link that can extend up to 160km.
10 Gigabit Ethernet Fiber Extender
Two 10 Gigabit Mode Media Converters can extend the distance between 10 Gigabit Multimode Switches across a fiber link up to 80km in length.
10 Gigabit Copper to Fiber Media Conversion
Convert your 10G XFP CX4 copper to multimode or single mode fiber. Ideal for large data centers and Co-Location applications where the distance required to connect top of rack switches exceeds the 100 meter limitation of 10G copper.
Click on a part number for ordering information
Product Image
Product Description
Power Cord & Part No.
S-10G-XTX - 10 Gigabit Ethernet Stand-alone Media Converter with dual XFP slots (empty)
S-10G-XTXH - 10 Gigabit Ethernet Stand-alone Media Converter with dual XFP slots (empty). Support Power Level 4 XFPs
Related Accessories
Accessory Image
Accessory Description
Part No.
DIN Rail Mounting Kit for 4 & 8 port IOLAN desktop models, all Stand-Alone Media Converters and all Stand-alone Ethernet Extenders. Two of these brackets are required for the 8 port STS8-D model.
Standalone media converter wall / rack mount bracket