eX-S1110-XT Gigabit Ethernet Extenders
10/100/1000 Industrial Temperature Copper Extender
- Extends 10/100/1000Base-T Ethernet up to 10,000 feet (3 KM) over 2-wire 24 AWG twisted pair
- Rugged-designed for harsh industrial -40°C to 75°C temperatures ( -40°F to 167°F )
- High-Speed – up to 200+ mbps aggregate line rate
- Transparent operation for all Ethernet protocols including 802.1Q VLAN packets and IP video compression schemes
- One or four 10/100/1000 Ethernet ports
- Advanced features: Link Pass-Through*, Interlink Fault Feedback*, Plug and Plan, Auto-MDIX and Loopback
When you need to extend Ethernet services beyond the general IEEE 802.3 limits of 328ft / 100m in extreme temperatures, and new fiber cabling is cost prohibitive, Ethernet Extenders are the perfect solution. Perle Ethernet Extenders transparently extend up to four 10/100/1000 Ethernet connections across copper wiring. Use single twisted pair (CAT5/6/7) or any existing copper wiring previously used in alarm circuits, E1/T1 circuits, RS-232, RS-422, RS-485, CCTV and CATV applications.
Equipment found in traffic management, oil and gas pipelines, weather tracking, industrial and outdoor applications must function in temperatures that cannot be supported by a commercial based Ethernet Extender. With the ability to operate in industrial grade temperatures of -40°F to +167°F (-40°C to +75°C) along with a rugged steel casing, these simple and effective point to point Ethernet Copper Extenders are ideal to extend the distance between two industrial Ethernet devices subjected to harsh environments and severe temperatures such as security cameras, wireless access points, alarms, traffic controllers, sensors and tracking devices.
Perle’s advanced features such as Link Pass-Through*, Interlink Fault Feedback*, and Loopback allow Network administrators to “see everything” for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle Ethernet Extenders the smart choice for IT professionals. eX-S1110 Ethernet Extenders are also available with support for Commercial Temperature ranges, managed networks with AAA security and high density applications.
eX-S1110-XT Gigabit Ethernet Extender Features
| Extend Ethernet over twisted pair | Extend an Ethernet link over category 5e, 6 and 7 cabling up to 10,000 feet (3 km) |
|
Extend Ethernet over Coaxial cable |
Extend an Ethernet link over 75 ohm coaxial cable |
|
High-Speed Performance |
Utilizes second generation VDSL2 technology (ITU-T Recommendation G.993.) . When operating under “Profile 30a”, Perle Ethernet extenders can provide an aggregate VDSL line rate capability of over 200 mbps. Actual distance and performance may vary depending on the type / gauge and condition of the wire used. |
|
Plug and Play operation |
Perle Ethernet Extenders will automatically configure your VDSL interlink connection. The CO/CPE peer association will be determined automatically by the Ethernet Extender. No need to set CO / CPE VDSL pairing. Once a connection is made, both ends will automatically adjust relevant VDSL parameters to optimize the level of bandwidth possible across the copper link. |
| Link Pass-Through* |
With Link Pass-Through the state of the 10/100/1000Base-T Ethernet connection is “passed through” the VDSL link to the 10/100/1000Base-T Ethernet connection on its remote peer. A managed switch on the remote end can then report the state (link up or link down) to its network management system so that any errors can be detected and recovered early. Competitive Ethernet extenders without this feature will never detect or report any error conditions. |
| Interlink Fault Feedback* | Similar to the Link Pass-Through feature, a loss of VDSL link will drop the 10/100/1000 Ethernet ports on each end until the link recovers. |
| Auto-Negotiation | The Ethernet Extender supports auto negotiation on the 10/100/1000Base-T interface. |
| Auto-MDIX | Auto-MDIX (Automatic Medium-Dependent Interface crossover) detects the signaling on the 10/100/1000 Ethernet RJ45 interface and determines the type of cable connected (straight-through or crossover) and automatically adopts a compatible pinout. |
| Fixed Speed and Duplex | Some Ethernet equipment require a fixed speed and duplex be used or cannot auto-negotiate. By disabling Auto-Negotiation on the Ethernet Extender, a fixed speed of 10, 100 or 1000 mbps as well as Full or half Duplex can be configured through DIP switches. |
| VLAN | Transparent to tagged VLAN (802.1Q) packets. |
| Transparent to IP Video compression protocols | Fully transparent to such IP video compression schemes such as MPEG-4, H.264 and MJPEG. |
| Power Strain Relief strap | A strain relief strap is provided to ensure a solid and secure power connection to the Ethernet Extender. Ideal for areas that may be exposed to vibration. |
| Loopback | When enabled, will perform a loopback on the copper VDSL Interlink. |
Hardware Specifications: eX-S1110-XT Gigabit Ethernet Extenders
Ethernet
Port
eX-1S1110-XT
1 port RJ45 – 10/100/1000Base-T - Shielded
eX-4S1110-XT
4 port RJ45 – 10/100/1000 Base-T - Shielded
Auto-MDIX
Auto-MDIX enables proper operation with either straight-through or crossover cabling
Distance
Distance up to 100 meters (328 feet) as per IEEE 802.3
Maximum Frame Size
1522 bytes
VDSL – Interlink
RJ45, BNC, Terminal Block
Ethernet Extenders must be connected in pairs using unconditioned wire. Circuits that run through signal equalization equipment are not permitted.
TIP and RING are polarity insensitive. Surge suppression of 400 volts between TIP and RING. Choice of RJ45, BNC or terminal block models for VDSL link connector:
- RJ45 – RING pin 4, TIP pin 5 (TIA 568 A/B)
- BNC – Coaxial 50 and 75 ohm cable with BNC connector
- Terminal Block – 2 position screw connectors for use with twisted pair telephone, alarm or serial cabling between 19 (0.9 mm) and 26 AWG (0.44 mm).
VDSL2 Line Rate/Reach
Actual distance and rates experienced will depend on condition and gauge of wire used. This Rate/Reach table applies to 24 AWG (0.5 MM) twisted pair wiring on RJ45 (RJ) and terminal block (TB) models
| High Speed Asymmetric | |||
| Reach (Distance) | VDSL Rate (Mbps) | ||
| feet | meters | Downstream | Upstream |
| 500 | 152 | 101 | 92 |
| 1000 | 305 | 101 | 63 |
| 1500 | 457 | 90 | 38 |
| 2000 | 610 | 62 | 24 |
| 2500 | 762 | 55 | 10 |
| 3000 | 914 | 42 | 5 |
| 3500 | 1000 | 35 | 3 |
| High Speed Symmetric | |||
| Reach (Distance) | VDSL Rate (Mbps) | ||
| feet | meters | Downstream | Upstream |
| 500 | 152 | 101 | 101 |
| 1000 | 305 | 85 | 101 |
| 1500 | 457 | 62 | 47 |
| 2000 | 610 | 60 | 29 |
| 2500 | 762 | 44 | 14 |
| 3000 | 914 | 30 | 7 |
| 3500 | 1000 | 29 | 4 |
| Long Reach Symmetric | |||
| Reach (Distance) | VDSL Rate (Mbps) | ||
| feet | meters | Downstream | Upstream |
| 500 | 152 | 53 | 44 |
| 1000 | 305 | 53 | 43 |
| 2500 | 762 | 39 | 18 |
| 4000 | 1219 | 25 | 4 |
| 5500 | 1676 | 17 | 1.9 |
| 7000 | 2134 | 8 | 2.3 |
| 7500 | 2286 | 7 | 2.2 |
| 8000 | 2438 | 5 | 2.2 |
| Long Reach Asymmetric | |||
| Reach (Distance) | VDSL Rate (Mbps) | ||
| feet | meters | Downstream | Upstream |
| 500 | 152 | 78 | 16 |
| 1000 | 305 | 78 | 16 |
| 2500 | 762 | 55 | 10 |
| 4000 | 1219 | 31 | 0.8 |
| 5500 | 1676 | 20 | 0.6 |
| 7000 | 2134 | 11 | 0.6 |
| 7500 | 2286 | 10 | 0.6 |
| 8000 | 2438 | 8 | 0.6 |
Power
Input Supply Voltage
9 - 30 vDC, unregulated (12 vDC Nominal)
Current
eX-1S1110-XT
350 mA
eX-4S1110-XT
500 mA
Power Consumption (watts)
eX-1S1110-XT
4.2
eX-4S1110-XT
6.0
Power Connectors
5.5mm x 9.5mm x 2.1mm barrel socket and 2 pin terminal Block
eX-1S1110-XT
eX-4S1110-XT
Power Adapter
Universal AC/DC adapter
Optional Industrial Temperature 100-240v AC, regulated 12V DC adapter
Indicators
Power / TST
This green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.
CO - Local
Ethernet Extender is operating in CO VDSL mode
CPE - remote
Ethernet Extender is operating in CPE VDSL mode
ILNK
Indicates Link Status and activity on the Interlink (VDSL) port
ETH
Indicates link status and activity on Ethernet port(s).
Switches
Access
All switch settings are accessible through a side opening in the chassis
Rate/Reach
Two switches enable the user to select the right balance between speed and distance for their environment.
Signal to Noise Ratio
Selectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.
Auto-Negotiation (802.3u)
Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex.
Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.
Link Mode
eX-1S1110-XT
Standard (Default) – The 10/100/1000Base-T link remains active independent of the state of the Ethernet link on its remote peer.
Link Pass-Through- the state of the 10/100/1000Base-T Ethernet connection is 'passed through' or propagated across the VDSL link to the 10/100/1000Base-T Ethernet link on its remote Ethernet Extender peer. This enables a managed switch to report the state of the remote device to its network management system.
eX-4S1110-XT
N/A
Interlink Fault Feedback
eX-1S1110-XT
Enabled - A loss of VDSL link will drop the 10/100/1000 Ethernet port on each end until the link recovers
Disabled (Default) – The state of the VDSL link is not propagated to the 10/100/1000Base-T port
eX-4S1110-XT
N/A
Loopback
Enabled - The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its peer.
Disabled (Default - Up)
Set Ethernet Speed (Port 1)
When Auto-Negotiation switch is disabled, fixed speed can be set at 1000 (Default) or 100 or 10
Set Ethernet Duplex (Port 1)
When Auto-Negotiation switch is disabled, Duplex can be set at Full (Default) or Half
Environmental Specifications
Operating Temperature
-40°C to 75°C (-40°F to 167°F)
Storage Temperature
minimum range of -40°C to 85°C (-40°F to 185°F)
Operating Humidity
5% to 90% non-condensing
Storage Humidity
5% to 95% non-condensing
Operating Altitude
Up to 3,048 meters (10,000 feet)
Heat Output (BTU/HR)
eX-1S1110-XT
14.3
eX-4S1110-XT
20.5
MTBF (Hours)*
eX-1S1110-XT
466,861 Hours
eX-4S1110-XT
365,077 Hours
*Calculation model based on MIL-HDBK-217-FN2 @ 30°C
Mounting
Din Rail Kit
Optional
Rack Mount Kit
Optional
Product Weight and Dimensions
Weight
eX-1S1110-XT
0.33 kg, 0.73 lbs
eX-4S1110-XT
0.47 kg, 1.04 lbs
Dimensions
eX-1S1110-XT
120 x 80 x 35 mm, 4.7 x 3.1 x 1.4 inches
eX-4S1110-XT
130 x 115 x 35 mm, 5.1 x 4.5 x 1.4 inches
Packaging
Shipping Weight
eX-1S1110-XT
0.46 kg, 1.01 lbs
eX-4S1110-XT
0.65 kg, 1.43 lbs
Shipping Dimensions
170 x 260 x 70 mm, 6.7 x 10.2 x 2.8 inches
Regulatory Approvals
Emissions
- FCC Part 15 Class A, EN55022 Class A
- CISPR 32:2015/EN 55032:2015 (Class A)
- EN61000-3-2
Immunity
CISPR 24:2010/EN 55024:2010
Electrical Safety
- UL/EN/IEC 62368-1
- CAN/CSA C22.2 No. 62368-1
- UL 60950-1
- IEC 60950-1(ed 2); am1, am2
- EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
- CE
Environmental
Other
- ECCN: 5A991
- HTSUS Number: 8517.62.0020
- Perle Limited Lifetime Warranty
Application Diagrams
Extend 10/100/1000 Ethernet across Twisted Pair or Coaxial Wire in Harsh Temperature Areas
Extend a Gigabit Ethernet link beyond the 100 meter (328 feet) limit using Ethernet Extenders. Distances of up to 3 km (10,000 feet) can be achieved over twisted pair Cat 5, 6, or 7 cable.
Extend four 10/100/1000 Ethernet ports across Twisted Pair or Coaxial Wire
Extend four Ethernet ports up to 3 km (10,000 feet) over twisted pair Cat 5, 6, or 7 cable.
Click on a part number for ordering information
Product Image
Product Description
Power Cord & Part No.
eX-1S1110-RJ-XT - Gigabit Industrial Temperature Ethernet Extender - 1 port 10/100/1000Base-T (RJ-45). RJ45 Interlink ( VDSL2 ) connector
eX-1S1110-BNC-XT - Gigabit Industrial Temperature Ethernet Extender - 1 port 10/100/1000Base-T (RJ-45). BNC ( Coax ) Interlink ( VDSL2 ) connector
eX-1S1110-TB-XT - Gigabit Industrial Temperature Ethernet Extender - 1 port 10/100/1000Base-T (RJ-45). 2-pin Terminal Block Interlink ( VDSL2 ) connector
eX-4S1110-RJ-XT - Gigabit Industrial Temperature Ethernet Extender - 4 port 10/100/1000Base-T (RJ-45). RJ45 Interlink ( VDSL2 ) connector
eX-4S1110-BNC-XT - Gigabit Industrial Temperature Ethernet Extender - 4 port 10/100/1000Base-T (RJ-45). BNC ( Coax ) Interlink ( VDSL2 ) connector
eX-4S1110-TB-XT - Gigabit Industrial Temperature Ethernet Extender - 4 port 10/100/1000Base-T (RJ-45). 2-pin Terminal Block Interlink ( VDSL2 ) connector
Related Accessories
Accessory Image
Accessory Description
Part No.
Extended Temperature UK power adapter for 12 volt Extended Temperature Terminal Servers, Media Converters and Ethernet Extenders
Extended Temperature EU power adapter for 12 volt Extended Temperature Terminal Servers, Media Converters and Ethernet Extenders
Extended Temperature USA power adapter for 12 volt Extended Temperature Terminal Servers, Media Converters and Ethernet Extenders
Extended Temperature SA power adapter for 12 volt Extended Temperature Terminal Servers, Media Converters and Ethernet Extenders
Extended Temperature AUS power adapter for 12 volt Extended Temperature Terminal Servers, Media Converters and Ethernet Extenders
DIN Rail Mounting Kit for 4 & 8 port IOLAN desktop models, all Stand-Alone Media Converters and all Stand-alone Ethernet Extenders. Two of these brackets are required for the 8 port STS8-D model.
Standalone media converter wall / rack mount bracket
