The S-1110-XT Industrial Temperature Media Converters address the need for transparently connecting 10/100/1000 Ethernet equipment that operate in extreme temperatures to fiber optic cable. The S-1110-XT Media Converters will operate in industrial grade temperatures of -40°F to +167°F (-40°C to +75°C). Equipment found in traffic management, oil and gas pipelines, weather tracking, industrial and outdoor applications must function in temperatures that cannot be supported by a commercial based media converter. Boasting this extended temperature feature along with a rugged steel casing, the S-1110-XT Media Converter provides an economical path to extend the distance between two industrial devices subjected to harsh environments and severe temperatures such as security cameras, wireless access points, alarms, traffic controllers, sensors and tracking devices.

Network Administrators can "see-everything" with Perle's advanced features such as Auto-Negotiation, Auto-MDIX, Link Pass-Through, Fiber Fault Alert, and Loopback. This allows for more efficient troubleshooting and less on-site maintenance. These cost and time saving features, along with a lifetime warranty and free worldwide technical support, make Perle's S-1110-XT Industrial Temperature 10/100/1000 Media Converters the smart choice for IT professionals.

S-1110-XT 10/100/1000 to Fiber Industrial Temperature Media Converter Features

Auto-Negotiation (802.3u)

The media converter supports auto negotiation. The 1000Base-X fiber interface negotiates according to 802.3 clause 37. The 10/100/1000Base-T negotiates according to 802.3 clause 28 and 40. The 1000Base-X will link up with its partner after the highest common denominator (HCD) is reached and the copper has linked up with its partner. The 1000Base-X will continue to cycle through negotiation transmitting a remote fault of offline (provided this is enabled through the switch setting) until the copper is linked up and the HCDs match.

The media converter supports auto-negotiation of full duplex, half duplex, remote fault, full duplex pause, asymmetric pause and Auto MDI-X.

Auto-MDIX

Auto-MDIX (automatic medium-dependant interface crossover) detects the signaling on the copper ethernet interface to determine the type of cable connected (straight-through or crossover) and automatically configures the connection when enabled. The media converter can also correct for wires swapped within a pair.

The media converter will adjust for up to 120ns of delay skew between the 1000Base-T pairs.

Smart Link Pass-Through

 When the Link Mode switch is placed into Smart Link Pass-Through mode, the copper ethernet port will reflect the state of the 1000Base-X media converter port. This feature can be used whether fiber auto-negotiation is enabled or disabled.

Fiber Fault Alert

 With Fiber Fault Alert the state of the 1000Base-X receiver is passed to the 1000Base-X transmitter. This provides fault notification to the partner device attached to the 1000Base-X interface of the media converter. If the 1000Base-X transmitter is off as a result of this fault it will be turned on periodically to allow the condition to clear should the partner device on the 1000Base-X be using a similar technique. This eliminates the possibility of lockouts that occur with some media converters. Applies only when fiber auto-negotiation is disabled.
Pause (IEEE 802.3xy) Pause signaling is an IEEE feature that temporarily suspends data transmission between two devices in the event that one of the devices becomes overwhelmed. The media converter supports pause negotiation on the 10/100/1000Base-T connection and 1000Base-X fiber connection.
Duplex Full and half duplex operation supported.
Jumbo Packets Transparent to jumbo packets up to 10KB.
VLAN Transparent to VLAN tagged packets.
Remote Loopback Capable of performing a loopback on the 1000Base-X fiber interface.

Hardware Specifications: S-1110-XT Industrial Media and Rate Converters

Power

Input Supply Voltage

6 - 30 vDC, unregulated (12 vDC Nominal)

Current

175 mA @ 12 vDC

Power Consumption

2.1 watts

Power Connector

2-pin pluggable terminal block

Indicators

Power / TST

This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode.

Fiber link on / Receive activity (LKF)

This green LED is operational only when power is applied. The LED is on when the 1000Base-X link is on and flashes with a 50% duty cycle when data is received.

Copper link on / Receive activity (LKC)

This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-T link is on and flashes with a 50% duty cycle when data is received.

Fiber Duplex (FDF)

This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-X link is operational in full duplex mode. The LED is off when in half duplex.

Copper Duplex (FDC)

This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-T link is operational in full duplex mode. The LED is off when in half duplex.

10/100/1000 Speed

This multi-color LED is operational only when power is applied. The LED is green when the speed of the copper ethernet port is running at 1000 Mbps. The LED is orange when the speed of the copper Ethernet port is running at 100 Mbps. The LED is off when in 10 Mbps.

Switches - accessible through a side opening in the chassis

Auto-Negotiation (802.3u)

  • Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex, half duplex, pause and remote fault capabilities.
  • Disabled - The media converter sets the port according to the position of the speed and duplex switches.

Link Mode

Link Mode provides a transparency to the state of the copper link allowing for simplified trouble shooting from the devices connected to the media converter.

Normal (Default — Up)

  • With Fiber Auto Negotiation enabled when the copper link goes down the 1000Base-X link is brought down. The 1000Base-X link will advertise Remote Fault (Link Fault).
  • With Fiber Auto Negotiation disabled the state of the copper link has no effect on the 1000Base-X link.

Smart Link Pass Through (Down)

  • With Fiber Auto Negotiation enabled the behavior is as follows. When the copper link goes down the 1000Base-X link is brought down. The 1000Base-X link will advertise Remote Fault (Link Fault). When Remote Fault (Link Fault) is received on the 1000Base-X interface the copper transmitter will be turned off. When the copper receiver is off the 1000Base-X transmitter will be turned off. When the 1000Base-X receiver goes off the copper transmitter will be turned off.
  • With Fiber Auto-Negotiation disabled the behavior is as follows. When the copper receiver is off the 1000Base-X transmitter will be turned off. When the 1000Base-X receiver goes off the copper transmitter will be turned off.

Fiber Fault Alert

The Fiber Fault Alert switch has meaning when Auto-Negotiation is disabled

  • Enabled (Default - Up)
    When the 1000Base-X receiver is off the 1000Base-X transmitter is turned off. Periodically the 1000Base-X receiver will be turned on for a short period to allow the condition to clear if the 1000Base-X link partner is using a similar feature.
  • Disabled (Down)

Remote Loopback

The media converter can perform a loopback on the 1000Base-X fiber interface.

  • Disabled (Default - Up)
  • Enabled - The 1000Base-X receiver is looped to the 1000Base-X transmitter. The copper transmitter is taken off the interface.

Auto-MDIX (Internal Strap)

  • If Auto-Negotiation (802.3u) is enabled, the media converter determines the current cable pinout to use on the copper interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the copper interface to set the port MDI or MDIX whichever is appropriate.
  • Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable.
  • Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting.

Speed Copper

  • 100 (Default)
  • 10

Duplex Copper

  • Full (Default)
  • Half

Duplex Fiber

  • Full (Default)
  • Half

Connectors

10/100/1000Base-T

RJ45 connector
  • 2 pair CAT5, EIA/TIA 568A/B or better cable for 10/100.
  • 4 pair CAT5 UTP cable for Gigabit.

Magnetic Isolation

1.5kv

Filtering

Filtering

1024 MAC Addresses

Frame Specifications

Buffer

1000 Kbits frame buffer memory

Size

  • Maximum frame size of 10,240 bytes -- Gigabit
  • Maximum frame size of 2048 bytes -- Fast Ethernet

Environmental Specifications

Operating Temperature

-40°C to 75°C (-40°F to 167°F)

Storage Temperature

-40°C to 75°C (-40°F to 167°F)

Operating Humidity

5% to 90% non-condensing

Storage Humidity

5% to 95% non-condensing

Operating Altitude

Up to 3,048 meters (10,000 feet)

Heat Output (BTU/HR)

  • 7.2 BTU

MTBF (Hours)*

475,616 Hours

Calculation model based on MIL-HDBK-217-FN2 @ 30°C

Chassis

Metal with an IP20 ingress protection rating

Mounting

Din Rail Kit

Optional

Rack Mount Kit

Optional

Product Weight and Dimensions

Weight

0.3 kg, 0.7 lbs

Dimensions

120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches

Packaging

Shipping Weight

0.43 kg, 1.0 lbs

Shipping Dimensions

150 x 210 x 40 mm, 5.9 x 8.3 x 1.6 inches

Regulatory Approvals

Emissions

  • FCC Part 15 Class A, EN55022 Class A
  • CISPR 22 Class A
  • CISPR 32:2015/EN 55032:2015 (Class A)
  • CISPR 24:2010/EN 55024:2010
  • EN61000-3-2

Immunity

EN55024

Electrical Safety

  • UL/EN/IEC 62368-1
  • CAN/CSA C22.2 No. 62368-1
  • UL 60950-1
  • IEC 60950-1(ed 2); am1, am2
  • EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
  • CE

Laser Safety

  • EN 60825-1
  • Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11.

Environmental

Reach, RoHS and WEEE Compliant

Other

  • ECCN: 5A991
  • HTSUS Number: 8517.62.0020
  • Perle Limited Lifetime Warranty

Select a Model to obtain a Part Number - S-1110-XT Industrial Temperature Media Converter

Model Connector Type Transmit
(dBm) 		Receive
(dBm) 		Power
Budget
(dBm) 		Wavelength
(nm) 		Fiber
Type 		Core
Size
(um) 		Modal
Bandwidth
(MHz* Km) 		Operating
Distance
Min Max Min Max
S-1110-M2SC05-XT Dual SC 1000Base-SX -9.5 -4.0 -17.0 -3.0 7.5 850 MMF
62.5
160
220 m
(722 ft)
62.5
200
275 m
(902 ft)
50
400
500 m
(1,640 ft)
50
500
550 m
(1,804 ft)
50
2000
1000 m
(3281 ft)
S-1110-M2ST05-XT Dual ST 1000Base-SX -9.5 -3.0 -20.0 -3.0 10.5 850 MMF
62.5
160
220 m
(722 ft)
62.5
200
275 m
(902 ft)
50
400
500 m
(1,640 ft)
50
500
550 m
(1,804 ft)
50
2000
1000 m
(3281 ft)
S-1110-M2LC05-XT Dual LC 1000Base-SX -9.5 -3.0 -20.0 -3.0 10.5 850 MMF
62.5
160
220 m
(722 ft)
62.5
200
275 m
(902 ft)
50
400
500 m
(1,640 ft)
50
500
550 m
(1,804 ft)
50
2000
1000 m
(3281 ft)
S-1110-S2SC10-XT Dual SC 1000Base-LX/LH -9.5 -3.0 -20.0 -3.0 10.5 1310 MMF*
62.5
500
550 m
(1,804 ft)
50
400
550 m
(1,804 ft)
50
400
550 m
(1,804 ft)
SMF
**
-
10 km
(6.2 mi)
S-1110-S2ST10-XT Dual ST 1000Base-LX/LH -9.5 -3.0 -20.0 -3.0 10.5 1310 MMF*
62.5
500
550 m
(1,804 ft)
50
400
550 m
(1,804 ft)
50
400
550 m
(1,804 ft)
SMF
**
-
10 km
(6.2 mi)
S-1110-S2LC10-XT Dual LC 1000Base-LX/LH -9.5 -3.0 -20.0 -3.0 10.5 1310 MMF*
62.5
500
550 m
(1,804 ft)
50
400
550 m
(1,804 ft)
50
400
550 m
(1,804 ft)
SMF
**
-
10 km
(6.2 mi)

Single Fiber Models Recommended use in pairs

Model Connector Type Transmit
(dBm) 		Receive
(dBm) 		Power
Budget
(dBm) 		Wavelength
(nm) 		Fiber
Type 		Core
Size
(um) 		Modal
Bandwidth
(MHz* Km) 		Operating
Distance
Min Max Min Max
S-1110-S1SC10U-XT
Single SC
1000Base-BX-U
-9.0
-3.0
-20.0
-3.0
11.0
1310 / 1490
SMF
**
-
10 km
(6.2 mi)
S-1110-S1SC10D-XT
Single SC
1000Base-BX-D
-9.0
-3.0
-20.0
-3.0
11.0
1490 / 1310
SMF
**
-
10 km
(6.2 mi)

The minimum fiber cable distance for all converters listed is 2 meters.

*A mode-conditioning adapter as specified by the IEEE standard, is required regardless of the span length. Note how the mode conditioning adapter for 62.5-um fibers has a different specification from the mode-conditioning adapter for 50-um fibers.

**ITU-T G.652 SMF as specified by the IEEE 802.3z standard.

Media Converter Accessories
4 DIN Rail Mount Bkt DIN Rail Mounting Kit
MCSM Standalone media converter wall mount bracket
04030674 Extended Temperature USA power adapter for 12 Volt Industrial Temperature Media Converter
04030671 Extended Temperature UK power adapter for 12 Volt Industrial Temperature Media Converter
04030672 Extended Temperature EU power adapter for 12 Volt Industrial Temperature Media Converter
04030675 Extended Temperature SA power adapter for 12 Volt Industrial Temperature Media Converter
04030676 Extended Temperature AUS power adapter for 12 Volt Industrial Temperature Media Converter

Application Diagrams

Fast Ethernet to IP Cameras

Connect 10/100/1000 IP Cameras to Fast Ethernet Backbone

Extend the reach to IP cameras using industrial fiber media converters. Security cameras are typically installed in remote locations where extremely high or low temperatures are a concern -- ceilings, rooftops, light poles, along fences, pipelines and transit routes.

Stand-alone Extended Temperature Media Converters are placed at the remote end connecting cameras with copper interfaces to fiber optic cabling. The fiber can extend the distance up to 20 kilometers using single mode or multimode fiber back to a control center. A media converter chassis located in the data closet at the control center accepts the fiber signal, converts it, and connects to the copper equipment at the main site.

Fast Ethernet to IP Cameras Diagram

Fast Ethernet Fiber to Wireless Access Points

Connect 10/100/1000 Wireless Access Points to Fast Ethernet Backbone

Extend the reach to wireless access points ( AP ) using fiber media converters. When a company deploys a wireless network in their office or large warehouse, APs need to be set up throughout the facility to ensure complete coverage for reliability. The network manager will likely need to extend further than the 100 meters allowed by copper cable to reach many of the APs.

When APs are used in industrial environments where extremely high or low temperatures are a concern, Stand-alone Extended Temperature Media Converters are placed at the remote end connecting APs with copper interfaces to fiber optic cabling. The fiber can extend the distance up to 20 kilometers using single mode or multimode fiber back to a control center. A media converter chassis located in the data closet at the control center accepts the fiber signal, converts it, and connects to the copper equipment at the main site.

Fast Ethernet Fiber to Wireless Access Points Diagram

Bridge 10/100 Devices to gigabit Backbone

Connect 10/100 devices to Gigabit Backbone

Industrial switches are often used in environments where extremely high or low temperatures are a concern. Devices in an industrial environment can be connected to a Gigabit backbone through the use of rate converting Industrial Temperature Media Converters.

Bridge 10/100 Devices to gigabit Backbone Diagram

Single Mode / Single Fiber

Connect copper ports over a single fiber strand ( also referred to as “Bi-Directional” BiDi )

When Single Strand fiber is used, a pair of Single Fiber Media Converters is needed for the copper to fiber conversion. Perle Single Fiber Media Converters are also referred to as “Up/Down” models. For example the S-1110-S1SC10U-XT (“Up”) and S-1110-S1SC10D-XT (“Down”), shown below, must be used in pairs. An “Up” must be matched with a “Down” peer to deal with transmit and receive frequencies separately.

Single Mode Fiber Diagram

S-1110-S1SC10U-XTS-1110-S1SC10D-XT


The majority of installations for single mode fiber media converters are of the “dual connector” or “dual fiber” type where one fiber connection is used for transmit, the other for receive. These are physically “crossed” to match up the Transmit/Receive links.

However, to reduce costs, or where there are limits on available fiber, WDM technology may be utilized. WDM uses separate transmit and receive frequencies to communicate on a single fiber strand. WDM technology relies on the fact that optical fibers can carry many wavelengths of light simultaneously without interaction between each wavelength. Thus, a single fiber can carry many separate wavelength signals or channels simultaneously.

So remember, if Single Strand fiber is used, you will need an “Up” Media Converter on one side and a “Down” Media Converter on the other for copper to fiber conversion.

Perle offers a wide variety of Single Fiber (“Up/Down”) Media Converters to connect 10BaseT, Fast Ethernet and Gigabit to single fiber. Whether you need Managed or Unmanaged, Standalone or Modular Chassis Based, 20km or 120km, Perle has the right model to meet your fiber conversion requirement.

Link Passthrough - Maintaining a Transparent Copper-Ethernet to Fiber Link

Fiber to Ethernet Converters

Understanding the need for an onboard processor in the media converter that continuously monitors the status of the links connected to its transceiver ports.

Media Converters enable Gigabit Ethernet over 2km Multimode fiber

Fiber to Ethernet Converters

Perle offers Gigabit Media Converters that enable Gigabit speeds across a multimode fiber link up to 2km in length to avoid the cost, complications, and lead times associated with the installation of new fiber.

Calculating and Understanding Optical Power Budgets

Fiber Media Converter

The steps explain how to keep the remaining available power budget number positive, so you can be assured that your fiber network will deliver the required performance over the life of the installation.

Lockheed Martin integrate Perle Fiber Media Converters

Media Converter Application Diagram for Lockheed Martin

Lockheed Martin moved sensitive equipment from harsh conditions to a Comms Room and replaced the PC with solid-state technology to handle the data imagery equipment using Perle's Media Converters for copper to fibre conversion for the network link.

York University use Perle Media Converters in Field Robotics Research Network

York University diagram

Perle Gigabit Media Converters provide fiber to copper conversion and POE+ to WLAN Access Points inside NEMA Weatherproof Enclosures.

Cambridge University selects Perle PoE+ Industrial Media Converters

Access point next to specially-designed lamp post housing unit

Perle PoE+ Industrial Media Converters enable over 30,000 connections at the Tour de France event.

Jorin and Perle Join Forces to Reduce Oil Pollution in the Water Supply

Device Server

Jorin upgraded to a Gigabit IP camera, needing a Rate Converting Media Converter. Perle Media Converters fulfilled connectivity, temperature, and size requirements and increased processing and transmission speeds, guaranteed reliability, and future-proofed the installation.

NBC Universal use Perle Industrial Switch and Media Converter to enable device control of Ethernet enabled satellite amplifiers greater than 300ft from a switch

NBC Universal Ethernet Extender Network Diagram

NBCUniversal use Perle Industrial Switch and Media Converter to gain device control of Ethernet enabled satellite amplifiers greater than 300ft from a switch. The setup is an inexpensive way to expand the network.

Golden Gate Bridge implements Perle Media Converters back to back to enable Gigabit Ethernet transmission of video feeds across Multimode (MM) Fiber

Golden Gate Bridge network diagram

Perle's gigabit media converters helped Golden Gate Bridge Highway & Transportation District double fiber distance without losing bandwidth. The cost-effective and reliable solution met all requirements for easy installation and effective use.

Mullglen install Perle Fiber Media Converters to remove EMI from Sonar Data Transmission

Mullglen Nedia Converters

Mullglen solved five years of unreliable sonar data transmission on fishing trawlers by installing Perle Fiber Media Converters, which eliminated EMI interference and enabled the use of a fiber network for transmission of sonar fish finder data.

PRG Gear use Perle PoE+ Media Converters for Coldplay Tour

PoE Media Converters power multiple video cameras

PRG Gear engineers rely on Perle Fiber Media Converters and PoE Mid-span Injectors to ensure reliable power and connectivity for concert tour equipment. These rugged devices are capable of withstanding fluctuating conditions.

Navtech use Perle Industrial Switches & Media Converters in military airbourne surveillance system

Drone Operators Navtech

Navtech Systems supplies airborne surveillance video downlinks globally, and secure, real-time transmission and distribution of data is crucial. Perle units are used in the network on the ground to access the imagery and data received from the aircraft. Perle products are high-quality, solid, secure, and reliable.

Stockton East Water District chooses Perle for fiber to Ethernet upgrade

Stockton

Stockton East Water District choose Perle for Fiber to Ethernet upgrade. Perle Media Converters connect a remote server room, over 2000 feet of multimode fiber, back to a main server room 1000Base-T Switch to improve network redundancy and reliability.

Creating a hybrid video surveillance system using Analog and IP Cameras

Diagram for Media Converters in Video Surveillance System

Dragon LNG installed Perle Fiber Media Converters to integrate new IP cameras into the existing surveillance system. Hybrid setup with analog cameras is flexible and scalable for more IP cameras in the future.

Priority Communications Select Perle Media Converters to Resolve Warehouse Ethernet Distance Limitations

Priority Communications Network Diagram

Installation of some multimode fiber and Perle Ethernet to Fiber Media Converters enabled the extension of the Ethernet network and improved network speed without any costly replacement of network infrastructure.

Gaming Innovation Group use Perle 10G Media Converters in Data Center

Diagram Igaming Cloud

Perle Media Converters facilitate Fiber to 10 GbE Copper Conversion at the GIG Data Center in Malta. They offer flexibility with different modules in one chassis and enable seamless and reliable connectivity for single mode and multimode equipment.

Sumitomo Metal Mining install Perle Media Converters to provide Fiber to Ethernet conversion in project to increase Internet Bandwidth

Fiber to Ethernet conversion in mountain top -20░F temperatures

To increase internet bandwidth, Sumitomo Metal Mining install Perle Media Converters to provide crucial Ethernet to Fiber conversion over Alaskan Mountain top in -20░F (-6░C) temperatures and over 12 inches of radial ice.

Pixact use Perle Media Converters to enable Real-time Visual Monitoring Process

Pixact cameras transmit images over CAT6

Pixact installed Perle Media Converters with SFP Optical Transceivers to connect 11 cameras to the fiber which are being used for product monitoring in a factory. The setup ensures reliable and real-time transfer of frames. The Perle Media Converters' rugged steel casing and ability to operate in extended temperatures made them the ideal choice.

ERH install Perle Media Converters in UK Smart Motorway

single mode single strand fiber

ERH upgraded 300 CCTV cameras in Wales with new HD Ethernet cameras. Perle media converters allowed multiple cameras to feed into a chassis unit for image transfer to the main network and video wall.

Enterprise Network fiber–optic deployment – Using Media Converters to unlock performance and reduce costs during upgrades

10/100/1000 to Gigabit

As the network upgrades are traditionally complex and expensive. Fiber to Copper Media Converters can simplify both of these issues for businesses and enable them to improve network performance.

Media Converters offer major benefits during Backhaul Network fiber-optic upgrades

Media Converters in Backhaul Network fiber-optic upgrades

Fiber to Ethernet Media Converters simplify the process by allowing businesses to use optical technologies to support high-bandwidth backhaul networks that connect to low-bandwidth Ethernet networks accessed by the end user.

Media Converters extend campus environment LANs

Media Converters in a Campus Environment Diagram

The use of chassis-based media converters is a cost effective means of providing fiber connectivity to enable long distance data transfer in campus networks.

Media Converters offer flexible expansion in Horizontal Networks

Fiber in Retail Application

Media Converters offer flexible expansion in Horizontal Networks. Media Converters ease the integration of fiber cabling to extend network distances avoid EMI disruptions and tighten data security

ISPs improve residential network performance through media conversion

Fiber in Residential Media Converter Diagram

ISPs improve residential network performance through media conversionby using media converters to integrate fiber-optic infrastructures and provide high-speed data services.

Media conversion can unlock the potential of Metropolitan Area Networks (MANs)

Metropolitan Area Network

Media Converters are essential for MAN deployment, facilitating seamless transition between the local Ethernet setup and the dark fiber. They enable consistent protocol handling during data transmissionresulting in significant performance enhancements over WAN systems.

Fiber to Ethernet can support large-scale retail networks

Integrating copper and fiber in a retail network

Integrating copper and fiber cabling in retail network environments

Avoiding common mistakes in fiber-optic network deployment

10/100/1000 to Gigabit

This is the first in a three-part series on major problems that can occur when businesses rush to deploy a fiber-optic cabling infrastructure.

Do I need an Ethernet Extender or a Media Converter?

Where to Start?

Understand when you need an Ethernet Extender or a Media Converter as they support a wide variety of protocols, data rates, and media types to integrate seamlessly into various network infrastructures.

Filter your options to find the right hardware for your application

Viewing 8 of 8 products

View Accessories

Click on a part number for ordering information

Product Image

Product Description

Power Cord & Part No.

S-1110-M2SC05-XT | 10-100-1000 Industrial Converter | Perle

S-1110-M2SC05-XT - 10/100/1000 Gigabit Ethernet Stand-Alone Industrial Temperature Media Rate Converter. 10/100/1000Base-T (RJ-45) to 1000Base-SX 850nm multimode (SC) [550 m/1804 ft.]. Extended Temperature, terminal block power connector for external power source.

S-1110-M2ST05-XT | 10-100-1000 Industrial Converter | Perle

S-1110-M2ST05-XT - 10/100/1000 Gigabit Ethernet Stand-Alone Industrial Temperature Media Rate Converter. 10/100/1000Base-T (RJ-45) to 1000Base-SX 850nm multimode (ST) [550 m/1804 ft.]. Extended Temperature, terminal block power connector for external power source.

S-1110-S2SC10-XT | 10-100-1000 Industrial Converter | Perle

S-1110-S2SC10-XT - 10/100/1000 Gigabit Ethernet Stand-Alone Industrial Temperature Media Rate Converter. 10/100/1000Base-T (RJ-45) [] to 1000Base-LX/LH 1310 nm single mode (SC) [10 km/6.2 miles] or multimode (SC) [550 m/1804 ft.] using a mode conditioning adapter. Extended Temperature, terminal block power connector for external power source.

S-1110-S2ST10-XT | 10-100-1000 Industrial Converter | Perle

S-1110-S2ST10-XT - 10/100/1000 Gigabit Ethernet Stand-Alone Industrial Temperature Media Rate Converter. 10/100/1000Base-T (RJ-45) [] to 1000Base-LX/LH 1310 nm single mode (ST) [10 km/6.2 miles]. Extended Temperature, terminal block power connector for external power source.

S-1110-S1SC10U-XT | 10-100-1000 Industrial Converter | Perle

S-1110-S1SC10U-XT - 10/100/1000 Gigabit Ethernet Stand-Alone Industrial Temperature Media Rate Converter. 10/100/1000Base-T (RJ-45) [] to 1000Base-BX 1310nm TX / 1490nm RX single strand fiber, single mode (SC) [10 km/6.2 miles]. Extended Temperature, terminal block power connector for external power source.

S-1110-S1SC10D-XT | 10-100-1000 Industrial Converter | Perle

S-1110-S1SC10D-XT - 10/100/1000 Gigabit Ethernet Stand-Alone Industrial Temperature Media Rate Converter. 10/100/1000Base-T (RJ-45) [] to 1000Base-BX 1490nm TX / 1310nm RX single strand fiber, single mode (SC) [10 km/6.2 miles]. Extended Temperature, terminal block power connector for external power source.

S-1110-M2LC05-XT | 10-100-1000 Industrial Converter | Perle

S-1110-M2LC05-XT - 10/100/1000 Gigabit Ethernet Stand-Alone Industrial Temperature Media Rate Converter. 10/100/1000Base-T (RJ-45) [] to 1000Base-SX 850nm multimode (LC) [550 m/1804 ft.]. Extended Temperature, terminal block power connector for external power source.

S-1110-S2LC10-XT | 10-100-1000 Industrial Converter | Perle

S-1110-S2LC10-XT - 10/100/1000 Gigabit Ethernet Stand-Alone Industrial Temperature Media Rate Converter. 10/100/1000Base-T (RJ-45) [] to 1000Base-LX/LH 1310 nm single mode (LC) [10 km/6.2 miles] or multimode (SC) [550 m/1804 ft.] using a mode conditioning adapter. Extended Temperature, terminal block power connector for external power source.

Related Accessories

Accessory Image

Accessory Description

Part No.

Ext. Temp Power Adapter UK | Perle

Extended Temperature UK power adapter for 12 volt Extended Temperature Terminal Servers, Media Converters and Ethernet Extenders

Ext. Temp Power Adapter EU | Perle

Extended Temperature EU power adapter for 12 volt Extended Temperature Terminal Servers, Media Converters and Ethernet Extenders

Ext. Temp Power Adapter USA | Perle

Extended Temperature USA power adapter for 12 volt Extended Temperature Terminal Servers, Media Converters and Ethernet Extenders

Ext. Temp Power Adapter SA | Perle

Extended Temperature SA power adapter for 12 volt Extended Temperature Terminal Servers, Media Converters and Ethernet Extenders

Ext. Temp Power Adapter AUS | Perle

Extended Temperature AUS power adapter for 12 volt Extended Temperature Terminal Servers, Media Converters and Ethernet Extenders

4 DIN Rail Mount Bkt | Perle

DIN Rail Mounting Kit for 4 & 8 port IOLAN desktop models, all Stand-Alone Media Converters and all Stand-alone Ethernet Extenders. Two of these brackets are required for the 8 port STS8-D model.

MCSM Standalone media converter wall / rack mount bracket | Perle

Standalone media converter wall / rack mount bracket

UNO-PS/1AC/24DC/60W Power Supply Accessory| Perle

UNO-PS/1AC/24DC/60W DIN-Rail Power Supply: 24 VDC, 60 Watt with universal 85 to 264 VAC, -25 to 70°C extended operating temperature.

Hi!

Have a Question? Chat with a live Product Specialist!

Have a Question?

We can provide more information about our products or arrange for a price quotation.


email-icon Send an Email
contactus-icon Send an Email callus-icon Call Us
×

Send us an Email